quantization

Quantization

Yao Wang
Polytechnic University, Brooklyn, NY11201
http://eeweb.poly.edu/~yao

Outline

• Review the three process of A to D conversion
• Quantization
– Uniform
– Non-uniform
• Mu-law
– Demo on quantization of audio signals
– Sample Matlab codes
• Binary encoding
– Bit rate of digital signals
• Advantage of digital representation

©Yao Wang, 2006 EE3414:Quantization 2

Three Processes in A/D Conversion

Sampling Quanti- Binary
zation Encoding
xc(t) x[n] = xc(nT) x[n] c[n]

Sampling Quantization Binary
Period Interval codebook
T Q

• Sampling: take samples at time nT
– T: sampling period;
– fs = 1/T: sampling frequency
• Quantization: map amplitude values into a set of discrete values kQ
– Q: quantization interval or stepsize
• Binary Encoding
– Convert each quantized value into a binary codeword


Analog to Digital Conversion

1
T=0.1
Q=0.25

0.5

0

-0.5

A2D_plot.m

-1

0 0.2 0.4 0.6 0.8 1


How to determine T and Q?

• T (or fs) depends on the signal frequency range
– A fast varying signal should be sampled more frequently!
– Theoretically governed by the Nyquist sampling theorem
• fs > 2 fm (fm is the maximum signal frequency)
• For speech: fs >= 8 KHz; For music: fs >= 44 KHz;
• Q depends on the dynamic range of the signal amplitude and
perceptual sensitivity
– Q and the signal range D determine bits/sample R
• 2R=D/Q
• For speech: R = 8 bits; For music: R =16 bits;
• One can trade off T (or fs) and Q (or R)
– lower R -> higher fs; higher R -> lower fs
• We considered sampling in last lecture, we discuss quantization
in this lecture


Uniform Quantization

• Applicable when the signal is in
a finite range (fmin, fmax)

• The entire data range is divided
into L equal intervals of length Q
(known as quantization interval or
quantization step-size)

Q=(fmax-fmin)/L

• Interval i is mapped to the
middle value of this interval

• We store/send only the index of
f − f min 
quantized value Index of quantized value = Qi ( f ) = 

 Q 
Quantized value = Q ( f ) = Qi ( f )Q + Q / 2 + f min


Special Case I:
Signal range is symmetric

• (a) L=even, mid-rise
Q(f)=floor(f/q)*q+q/2

L = even, Mid - Riser L = odd, Mid - Tread
f Q f
Qi ( f ) = floor ( ), Q ( f ) = Qi ( f ) * Q + Qi ( f ) = round ( ), Q( f ) = Qi ( f ) * Q
Q 2 Q


Special Case II:
Signal range starts at 0

f min = 0, B = f max , q = f max / L
f
Qi ( f ) = floor ( )
Q
Q
Q( f ) = Qi ( f ) * Q +
2


Example

• For the following sequence {1.2,-0.2,-0.5,0.4,0.89,1.3…}, Quantize it using a
uniform quantizer in the range of (-1.5,1.5) with 4 levels, and write the quantized
sequence.
• Solution: Q=3/4=0.75. Quantizer is illustrated below.

-1.125 -0.375 0.375 1.125

-1.5 -0.75 0 0.75 1.5

Yellow dots indicate the partition levels (boundaries between separate quantization intervals)
Red dots indicate the reconstruction levels (middle of each interval)

1.2 fall between 0.75 and 1.5, and hence is quantized to 1.125

• Quantized sequence:
{1.125,-0.375,-0.375,0.375,1.125,1.125}


Effect of Quantization Stepsize

Q=0.25 Q=0.5
1.5 1.5

1 1

0.5 0.5

0 0

-0.5 -0.5

-1 -1

-1.5 -1.5
0 0.2 0.4 0 0.2 0.4
demo_sampling_quant.m


Demo: Audio Quantization

0.02

original at 16 bit
Original 0.015 quantized at 4 bit
Mozart.wav
0.01

0.005
Quantized
Mozart_q16.wav
0

-0.005

-0.01
2 2.002 2.004 2.006 2.008 2.01 2.012 2.014 2.016 2.018 2.02
4
x 10


Demo: Audio Quantization (II)

0.02 0.02
original at 16 bit
quantized at 6 bit
original at 16 bit
0.015 quantized at 4 bit 0.015

0.01 0.01

0.005 0.005

0 0

-0.005 -0.005

-0.01 -0.01
2 2.002 2.004 2.006 2.008 2.01 2.012 2.014 2.016 2.018 2.02 2 2.002 2.004 2.006 2.008 2.01 2.012 2.014 2.016 2.018 2.02
4 4
x 10 x 10

Quantized Quantized
Mozart_q16.wav Mozart_q64.wav


Non-Uniform Quantization

• Problems with uniform quantization
– Only optimal for uniformly distributed signal
– Real audio signals (speech and music) are more
concentrated near zeros
– Human ear is more sensitive to quantization errors at small
values
• Solution
– Using non-uniform quantization
• quantization interval is smaller near zero


Quantization: General Description

Quantization levels : L
Partition values : bl
Partition regions : Bl = [bl −1 , bl )
Reconstruction values : g l
Quantized Index : Qi ( f ) = l , if f ∈ Bl
Quantizer value : Q( f ) = g l , if f ∈ Bl


Function Representation

Q ( f ) = gl , if f ∈ Bl


Design of Non-Uniform Quantizer

• Directly design the partition and reconstruction levels
• Non-linear mapping+uniform quantization
µ-law quantization


µ-Law Quantization

y =F [ x ]
 |x| 
log 1+µ
 X max 
.sign[ x]
= X max
log[1 + µ ]


Implementation of µ-Law Quantization
(Direct Method)

– Transform the signal using µ-law: x->y
y =F [ x ]
 |x| 
log 1+µ
X max 
= X max  .sign[ x]
log[1 + µ ]

– Quantize the transformed value using a uniform quantizer: y->y^
– Transform the quantized value back using inverse µ-law: y^->x^

x =F −1[ y ]
X  log(1+ µ ) y 
= max 10 X max − 1 sign(y)
µ  
 


Implementation of µ-Law Quantization
(Indirect Method)

• Indirect Method:
– Instead of applying the above computation to each sample,
one can pre-design a quantization table (storing the partition
and reconstruction levels) using the above procedure. The
actual quantization process can then be done by a simple
table look-up.
– Applicable both for uniform and non-uniform quantizers
– How to find the partition and reconstruction levels for mu-law
quantizer
• Apply inverse mu-law mapping to the partition and
reconstruction levels of the uniform quantizer for y.
• Note that the mu-law formula is designed so that if x ranges
from (-x_max, x_max), then y also has the same range.


Example

• For the following sequence {1.2,-0.2,-0.5,0.4,0.89,1.3…}, Quantize it
using a mu-law quantizer in the range of (-1.5,1.5) with 4 levels, and
write the quantized sequence.

• Solution (indirect method):
– apply the inverse formula to the partition and reconstruction levels found for
the previous uniform quantizer example. Because the mu-law mapping is
symmetric, we only need to find the inverse values for y=0.375,0.75,1.125
µ=9, x_max=1.5, 0.375->0.1297, 0.75->0.3604, 1.125->0.7706
– Then quantize each sample using the above partition and reconstruction
levels.


Example (cntd)

-1.125 -0.375 0.375 1.125

-1.5 -0.75 0 0.75 1.5

x =F −1[ y ]
Inverse µ-law
X  log(1+ µ ) y 
µ  
 
-0.77 -0.13 0.13 0.77

-1.5 -0.36 0 0.36 1.5

• Original sequence: {1.2,-0.2,-0.5,0.4,0.89,1.3…}
• Quantized sequence
– {0.77,-0.13,-0.77,0.77,0.77,0.77}

Uniform vs. µ-Law Quantization

Uniform: Q=0.5 µ-law: Q=0.5,µ=16
1.5 1.5

1 1
0.5 0.5

0 0

-0.5 -0.5
-1 -1

-1.5 -1.5
0 0.2 0.4 0 0.2 0.4

With µ-law, small values are represented more accurately,
but large values are represented more coarsely.


Uniform vs. µ-Law for Audio
0.02 0.02
q32 q64

0.01 0.01

0 0
Mozart_q32.wav Mozart_q64.wav

-0.01 -0.01
2 2.01 2.02 2 2.01 2.02
4 4
x 10 x 10
0.02 0.02
q32µ4 q32µ16
0.01 0.01

0
Mozart_q32_m4.wav 0
Mozart_q32_m16.wav

-0.01 -0.01
2 2.01 2.02 2 2.01 2.02
4 4
x 10 x 10

Evaluation of Quantizer Performance

• Ideally we want to measure the performance by how close is the
quantized sound to the original sound to our ears -- Perceptual
Quality
• But it is very hard to come up with a objective measure that
correlates very well with the perceptual quality
• Frequently used objective measure – mean square error (MSE)
between original and quantized samples or signal to noise ratio
(SNR)
1
MSE : σ q =
2

N
∑ ( x(n) − x(n))
n
ˆ 2

(
SNR(dB) : SNR = 10 log10 σ x / σ q
2 2
)
where N is the number of samples in the sequence.
1
σ x is the variance of the original signal, σ z2 = ∑ ( x(n)) 2
2

N n


Sample Matlab Code

Go through “quant_uniform.m”, “quant_mulaw.m”


Binary Encoding

• Convert each quantized level index into a codeword
consisting of binary bits
• Ex: natural binary encoding for 8 levels:
– 000,001,010,011,100,101,110,111
• More sophisticated encoding (variable length coding)
– Assign a short codeword to a more frequent symbol to
reduce average bit rate
– To be covered later


Example 1: uniform quantizer

• For the following sequence {1.2,-0.2,-0.5,0.4,0.89,1.3…}, Quantize it using a
uniform quantizer in the range of (-1.5,1.5) with 4 levels, and write the quantized
sequence and the corresponding binary bitstream.
• Solution: Q=3/4=0.75. Quantizer is illustrated below.
• Codewords: 4 levels can be represented by 2 bits, 00, 01, 10, 11

codewords 00 01 10 11

Quantized values -1.125 -0.375 0.375 1.125

-1.5 -0.75 0 0.75 1.5

• Quantized value sequence:
{1.125,-0.375,-0.375,0.375,1.125,1.125}
• Bitstream representing quantized sequence:
{11, 01, 01, 10, 11, 11}


Example 2: mu-law quantizer
codewords 00 01 10 11
-1.125 -0.375 0.375 1.125

-1.5 -0.75 0 0.75 1.5

x =F −1[ y ]
Inverse µ-law
X  log(1+ µ ) y 
codewords 00 01 10 11 µ  
 
-0.77 -0.13 0.13 0.77

-1.5 -0.36 0 0.36 1.5

• Original sequence: {1.2,-0.2,-0.5,0.4,0.89,1.3…}
• Quantized sequence: {0.77,-0.13,-0.77,0.77,0.77,0.77}
• Bitstream: {11,01,00,11,11,11}

Bit Rate of a Digital Sequence

• Sampling rate: f_s sample/sec
• Quantization resolution: B bit/sample, B=[log2(L)]
• Bit rate: R=f_s B bit/sec
• Ex: speech signal sampled at 8 KHz, quantized to 8 bit/sample,
R=8*8 = 64 Kbps
• Ex: music signal sampled at 44 KHz, quantized to 16 bit/sample,
R=44*16=704 Kbps
• Ex: stereo music with each channel at 704 Kbps: R=2*704=1.4
Mbps
• Required bandwidth for transmitting a digital signal depends on
the modulation technique.
– To be covered later.
• Data rate of a multimedia signal can be reduced significantly
through lossy compression w/o affecting the perceptual quality.
– To be covered later.


Advantages of Digital
Representation (I)
1.5
More immune to
noise added in original signal
channel and/or received signal
storage
1

The receiver applies
a threshold to the
received signal: 0.5

0 if x < 0.5
x=
ˆ
1 if x ≥ 0.5
0

-0.5
0 10 20 30 40 50 60


Advantages of Digital
Representation (II)

• Can correct erroneous bits and/or recover missing
bits using “forward error correction” (FEC) technique
– By adding “parity bits” after information bits, corrupted bits
can be detected and corrected
– Ex: adding a “check-sum” to the end of a digital sequence
(“0” if sum=even, “1” if sum=odd). By computing check-sum
after receiving the signal, one can detect single errors (in
fact, any odd number of bit errors).
– Used in CDs, DVDs, Internet, wireless phones, etc.


What Should You Know

• Understand the general concept of quantization
• Can perform uniform quantization on a given signal
• Understand the principle of non-uniform quantization, and can
perform mu-law quantization
• Can perform uniform and mu-law quantization on a given
sequence, generate the resulting quantized sequence and its
binary representation
• Can calculate bit rate given sampling rate and quantization
levels
• Know advantages of digital representation
• Understand sample matlab codes for performing quantization
(uniform and mu-law)


References

• Y. Wang, Lab Manual for Multimedia Lab, Experiment on
Speech and Audio Compression. Sec. 1-2.1. (copies provided).


quantization

Recommended

Recommended

More Related Content

What's hot

What's hot (20)

Viewers also liked

Viewers also liked (20)

Similar to quantization

Similar to quantization (20)

More from aniruddh Tyagi

More from aniruddh Tyagi (20)

Recently uploaded

Recently uploaded (20)

quantization